Thought it best to move this to the mod area and start a new thread.
Because most of the windows on the TM are not an awning type/style we added eyebrows or drip caps as they are known to some of our windows.
These are light weight aluminum and to my knowledge are not available in colors. For a light rain no wind blowing they will let you keep windows open.
You need to watch very carefully how you position the drip cap over the back shell side windows because of the front shell bag seals when closed.
A little bending may be required so the cap doesn't cut or chafe the bag seal.
Since the outside skin is very thin I used pop rivets to attach the drip caps or eyebrows. I used 1/8 by 1/8 rivets. Use masking tape on your drill bit as a depth gauge. After all the holes were drilled, use the drip cap as a templet, I put a bead of clear silicon on the drip cap mounting lip and starting at one installed the pop rivets. I used clear silicon as I felt it would be less noticeable than white. Any rv dealer should be able order the drip caps. Allow 1 to 2 inch over hang past the window edge. For the small windows my drip caps are 22 inch.
__________________
Axis 24.1 E 450 chassis, 6 spd tranny. GVWR 14500# GVCWR 22000 # GW(scales) 12400 #
[SIGPIC][/SIGPIC]
mods: 2- 100 watt solar panels, on roof, 300 watts portable
“They who would give up essential Liberty, to purchase a little temporary Safety, deserve neither Liberty nor Safety.” Benjamin Franklin
Last year Trailmanor sent me some self-adhesive plastic trim for putting above a window I was having leakage problems with. They also suggested putting it above the Frig vents.
It doesn't extend out as far as the Al stuff you use, but fixed my problem and was easy to put on. Not sure where you can get the stuff other than the factory ...
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,117
Several years ago, a couple people reported water coming in at the top of the entry door. It turned out that the water was coming off the roof, flowing down the sidewall behind the awning, and then down the outside wall to the top of the door. On earlier TMs there was an eyebrow above the door, but TM was experimenting with not installing it, relying instead on the caulking behind the awning. Perhaps because there is a little more flexing in that area, the caulking behind the awning failed in those two cases. Learning from its customers, TM went back to the eyebrow. And as I recall, the eyebrow was white, not bare aluminum. So they are available.
Bill
__________________
2020 2720QS (aka 2720SL)
2014 Ford F-150 4WD 5.0L Bill's Tech Stuff album
Our TM has the gutter over the door, those are also available and in colors. I went with the drip cap because they stick out about 2 inches and can be placed over the window where as the gutter is about 1/2 inch to 3/4 inch and mounts strictly above the window. The gutter does have a big plus...no holes to drill.
__________________
Axis 24.1 E 450 chassis, 6 spd tranny. GVWR 14500# GVCWR 22000 # GW(scales) 12400 #
[SIGPIC][/SIGPIC]
mods: 2- 100 watt solar panels, on roof, 300 watts portable
“They who would give up essential Liberty, to purchase a little temporary Safety, deserve neither Liberty nor Safety.” Benjamin Franklin
I am a huge FAN of Velcro thin white strips when I do things on the outside of the TM. I HATE drilling into the sides it makes me nervous. Clean the area that you want to place something and it will stay. A little caulk on top would work just fine. The best place to buy white Velcro is your nearest sewing/quilting shop in your area they have so many other neat things.
I had a plastic piece break off on the side of my TM and I did the Velcro and it will be there for ever, it is just like duck tape and vice grips I carry it with me all the time I gave up on glue and drilling.