Need to have better support for stove/oven

[dcrdark]

We just came back from up state New York for a family reunion. Going by way of I81 through PA, which is a wash board of a road. When I opened the TM I found that the stove/oven was almost on the floor, it would have been if the gas pipe was not conntected. All of the screws were torn loose and I spent most of a day making supports for beefing up around the stove area.

 

[Windbreaker]

Wow, I've been reading this board for two years now and that is a new one on me!

 

[live2shopnc]

The small bar that runs in front of mine fell off returuning home from my last trip.

 

[dcrdark]

When I was putting the stove back in place, I notice that something was missing in the front. We bought the TM used and thought it was susposed to be like that. Anyway, I did put a piece of poplar in the front. What I did to beef up the area was to remove the shelf under the stove. On the left side I took 3/4" plywood and ran it from the underside of the counter all the way to the floor. On the right side. I didn't want to take the cabinet apart so, where the drawer and the cabinet door is, I took some pieces of 3/4" plywood and glued and screwed them between the cabnet supports on the wall next to the stove. This gave me something more substantial to screw the the stove to. Since I did this, I was able to make supports for the bottom of the stove as well. At first the back of the stove was not supported and I think because of the bouncing the bakc of the stove started to rock and once the rocking started it couldn't stop. Anyway, after all this rambling, I still would like to see the stove supported better in the future.

Dave

 

[Bill]

There is a wooden cross-member under the front of the stove. It is not pressed up against the underside of the oven - as I recall it is about an inch below the front edge of the oven. I believe that this gap is intentional, and provides ventilation. Be careful not to close it up.

Bill

 

[dcrdark]

Thanks Bill,
I'll more than likely drill some large holes in it so that it will provide for both purposes.
Dave

 

[bpbenysh]

Oven Bounce

Have not had the oven work loose but did have the oven door come off after a particularly bad "crater" on I80 in PA. Had to straighten door hinge brackets before I could re-install. I'm considering some kind of restraint for the door.
Bill

 

[Carol-TMO]

Oven & Stove Top Bounce

We started using a bungee cord looped through the oven door handle and then hooked through the grate on the top to prevent the door from opening or the top grate from bouncing loose during travel.

Of course, this would not solve the entire oven unit from coming loose. Luckily, ours seems to be quite securely installed.

 

[Northwoods-TMO]

We've had similar problems. We now take the grate off and store it on the floor when underway. The screws have also come out of the foam and we're processing how to make that a permanent "fix/repair". The door has never com open, yet. The floor storage came about after we found the grate 'loose' in the trailer. Olga & Ken, Northwoods

 

[WNYChange]

Oven and Stove

I posted a message about a week ago in the maintanence section about this same problem. Seems like most of those replies said people didn't see this exact problem. I'm glad I spent some time hunting around this board tonight, because I see I'm not the only one having the same problem I am. I've also made added some supports and tried to tighten things up as much as possible. Someone posted a good idea about placing a pillow on the oven while traveling. I'm going to try that.

 

[G-V_Driver]

My post could have been the one you referenced regarding traveling with a pillow on the grate--thanks to Kate Unruh at The Car Show. A good tip, and a simple way to solve the problems that could be caused by a loose grill flailing around.

Now that I've had time to think about it, I have come to believe that loose grills and loose stoves are almost certainly separate issues requiring separate actions. I have put the "check stove mounting" item on my checklist for the next time the TM is open.

 

[Cateye]

We have the stove cover option, use our TM extensively on wash boarded/rough back roads and have not had these problems. Maybe the stove cover is the solution....

 

[harvsterg]

Pop Top Stove

Spent labor day weekend on south Jesery Shore. All smoth Highways from Baltimore to Cape May. The first morning while cooking breakfast I noticed the eggs were running to one side of ther pan .I knew I had leveled the unit. Then I noticed the whole top of the stove had poped up almost 1/2 inch in the back. It was easy to put back . I now believe the stories of ovens moving while traveling


Harvsterg
96 2720SL
96 Ford Explorer 5L V8
No WDH