TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Owners Community > TrailManor Technical Library
Register FAQ Members List Calendar Mark Forums Read

Closed Thread
 
Thread Tools Display Modes
Old 04-19-2018, 12:06 AM   #1
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default Poor Man's Thetford or Sealand Alternative


So I couldn’t get myself to pay for the Sealand 711 and we didn’t want to spend another season with the Thetford in our '04 2720. Looking around I found this 8.5 gallon holding tank made by Icon that is designed to have a toilet direct mount and reinforced to support the weight of a person. I ordered one from Amazon ($140) to see if it might work.

It seemed plenty sturdy so I decided to continue. I found a Thetford low profile toilet on eBay new for $95. For venting I decided to use a marine through hull vent from Amazon.
DudeAbides is offline  
Old 04-19-2018, 12:18 AM   #2
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default

The tank is 6” tall, so to secure it I built a box. I ripped a piece of 1x8 pvc trimboard down to 6” wide to build it with.

Then I drilled holes around the lip of the tank to secure it to the box with stainless screws.
I did this before opening the trailer. Once I removed the old toilet i realized I was going to have to modify. The discharge on the tank was located 3/4” closer to the frame rail in the trailer and 2” toward the tub from the hole in the floor. The 2” would be easy to trim off the existing hole but the 3/4” would put it on the trailer frame. Luckily the mounting flange on the tank is 1-1/4”, so I was able to trim off 3/4” from the back side.

Now I had to modify the box I built for the shortened back flange AND for the wheelwell interference I didn’t anticipate.
DudeAbides is offline  
Old 04-19-2018, 12:20 AM   #3
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default



Keep in mind the box only secures the tank in place, the tank itself is structural. The box I then screwed to the floor with some small L brackets and then screwed the tank down.

DudeAbides is offline  
Old 04-19-2018, 12:29 AM   #4
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default

For the vent I made a hole in the side right above the line from the tank.


For the water supply I enlarged the hole the power for the old toilet went through and ran pex to under the kitchen sink so it would be easier work with the fittings. I terminated the line with this push fitting supply line and valve combo.
DudeAbides is offline  
Old 04-19-2018, 12:36 AM   #5
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default

All in all it turned out pretty well.


Here you can see the discharge is the same distance from the frame rail as the original, just moved 2” to the rear of the trailer.


I’m currently repairing a crack in my grey tank so I haven’t completed the exterior plumbing yet. It’s easy though. A small stub of pvc glued to the threaded coupler in the bottom of the tank, then join to the old 3” with a rubber coupler. Then shorten the 1-1/2” side by 2” and reconnect with either a glued coupler or a rubber coupler. I will post pics once that part is completed.
DudeAbides is offline  
Old 04-19-2018, 12:57 AM   #6
DudeAbides
Member
 
Join Date: Jun 2017
Posts: 25
Default

Costs
Icon holding tank $140 on Amazon (currently listed at $147)
Thetford Aqua Magic low profile $95 on ebay
Marine through hull vent $12 Amazon
Push fittings and pex tubing (1 elbow, 1 tee, and 1 valve/supply line combo) $25 at Menards
3/4" vinyl hose for the vent $1.50 at Ace
1"x8"x8' pvc trim board $23 at Menards
Stainless screws ~$5 at Menards
3" and 1-1/2" rubber couplers ~$8 at Menards

I know there are a few things I'm probably missing but as you can see it came out to right about $300 and could have been cheaper with other choices.
DudeAbides is offline  
Closed Thread


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Installing a Thetford Curve Riwright Plumbing 47 10-14-2015 07:43 AM
Potential ideal alternative to the Thetford ShrimpBurrito Plumbing 10 07-15-2013 04:49 PM
Taming the Thetford "stinker". T and C Plumbing 5 10-20-2011 10:48 AM
More Thetford Good & Bad mcgyver210 Plumbing 4 09-19-2010 11:06 PM
Continuing problems with Thetford toilet nonichris Plumbing 63 01-13-2009 08:43 AM


All times are GMT -6. The time now is 04:05 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.