Reese WDH Trunnion bar defect (or owner defect?)

[pauloh]

I bought a Reese weight-distributing hitch (Reese 49586-020 Trunnion for WD Pro Series) a couple of months ago, from Amazon. (This was a package unit, all parts included in the box, nothing bought separate except my tow ball.) Finally trying to install it today, after studying the parts and instructions several times the past few weeks. I am at the stage of trying to insert the trunnion bars into the hitch. This I cannot seem to do no matter what I try. I am somewhat mechanically inclined, doing all the TM stuff like fixing fridge wiring, putting on tires, greasing bearings, etc. though perfectly capable of stupid mistakes. I looked at several videos at etrailer.com, none are identical to mine, but it seems you just insert the trunnion with it rotated parallel with TV's bumper (also per instructions here), then turn it back toward the TM. Mine just don't seem to go in far enough (lower pin) to allow the upper pin of the trunnion to slide into the groove there, or that upper pin hits before you get in far enough. THEN, I tried the trunnion upside down. It glided right into place. Mounted this way, the trunnion can wobble or rattle a little in it's locked position, but seems secure and I am guessing this is about how they feel when normally installed. I found one reference to Reese manufacturing parts wrong in another forum, is it possible this is my problem? I am in a rural area, no way to go check this somewhere at a dealer, but I could order another set of bars and see if I have the same issue I suppose. Thanks for setting me straight if you see what I've missed here. Several photos attached I hope will show what I'm seeing....does it look like the trunnion heads are upside down from the bars, by any chance? The bars are stamped "made in China" and I assume this would normally be on the bottom of the bar, which is where it is when the Reese label is upright on the trunnion head. But I don't know how the head/bar angle is supposed to normally look. The bar seems to taper downward toward the TM, which does seem like it should be. Haven't tried hooking up the chains or anything with the upside-down installation!

I have the identical hitch.

Place the bar at right angles to the shank, or angled even more toward the truck. Tilt the chain end of the bar toward the ground.

Tilt the top "pin" back toward the truck. (you seem to have it tilted more toward the trailer).

Put the bottom pin all the way into the hole. Or the top won't fit.
Lift up so the top pin is in position and rotate that bar toward the trailer.

And yes, the markings should NOT be upside-down.

Actually I had the same problem the first time, but there was somebody there to show me how to do it.

[pauloh]

Thanks, Bruce! I have tried again, both sides, both bars. I haven't gotten it yet. Trying to follow your advice to the letter. The bottom pin seemingly will not go all the way to its hole before the top pin (or shoulder of the top pin) hits the top part of the hitch/shank, there in its groove or nearby, no matter what angle I try. It just seems too "tall" or the shank/hitch area is too short (so it seems). There is a lot of paint on those pins, I've worn some off but I don't think that's it. I can see the groove I assume the top pin should align with to enter its hole (assuming the bottom pin would go all the way in.) The top pin hits in there and is stopped, before the bottom pin gets all the way in.

I'm glad to hear you had the same problem, I'm sure I just haven't found the technique yet. I do have my hitch/shank (and ball) tilted back a little so that may be why it looks like the pin is tilted back also. I cannot see a way to tilt the top pin more toward the truck without completely missing the groove for the top pin to slide in.

Thanks again, I'll try it with fresh muscles in the morning and if I do get it will report back. I was angrily contemplating another WDH but will try try again on this one. Might try calling the mfr. (800 # on the instructions) and see if they answer the phone. It was after 5 here when I ran into this issue today, so thanks again for your reply.

What you need is a YouTube video of this. Maybe one exists already? (EDIT: Oh, I see you've already looked)

Anyway, if you still have a problem (and if it ever stops raining here), I'll go out and take a series of photos of the way i do it.

Who knows, although your equipment looks ok from here, it may just be out of spec in some way.

OK, it stopped raining!
Here's a photo of the angles I use to get it in:
Hitch Bar Install

Turns out I don't really tilt the top pin back toward the truck. But the whole bar is angled toward the truck and down to the ground as in the picture. I can then insert the lower pin into its hole and lift up on the chain end of the bar to get the top pin into position. Then rotate the chain end of the bar back to the trailer.

Hope this helps.