TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Technical Discussions > Plumbing
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 09-30-2024, 02:26 PM   #11
Dan3023
Member
 
Join Date: Aug 2024
Posts: 17
Default

I have tried looking at a 2" reducer. The problem is that the 2" is the ID, not rhe OD. I think I'm either going to try some JB plasti-weld or just some marine sealant and goop it up good. At this point, I'm thinking about just making one. I don't like the 1/4" lip at the drain. If I make one, I can do it right. I kind of wish I would have just made one from the start.
Dan3023 is online now   Reply With Quote
Old 09-30-2024, 05:14 PM   #12
ShrimpBurrito
Site Sponsor
 
ShrimpBurrito's Avatar
 
Join Date: Jul 2006
Location: Sunny Beaches of Los Angeles
Posts: 3,276
Default

Look here for a bunch of ABS fittings with an OD of 1 29/32". That equates to a bit over 1/32" on each side in a 2" hole, which might be a small enough gap to be sealed with some ABS cement. If there end up being any gaps, you could make some ABS paste from shavings and cement to seal them.

https://www.mcmaster.com/products/st...bs/od~1-29-32/

Dave
__________________
2000 2720SL & 2007 3124KB
2005 Toyota Sequoia
Twin Battle Born 12v 100Ah LiFePO4 (BBGC2) batteries, 300W solar on rear shell, Link 10, Lift kit, Maxxis 8008 225 75/R15 E tires
ShrimpBurrito is online now   Reply With Quote
Old 09-30-2024, 10:38 PM   #13
Wavery
TrailManor Master
 
Wavery's Avatar
 
Join Date: Jan 2022
Location: San Diego, California
Posts: 2,934
Default

Quote:
Originally Posted by Dan3023 View Post
I have tried looking at a 2" reducer. The problem is that the 2" is the ID, not rhe OD. I think I'm either going to try some JB plasti-weld or just some marine sealant and goop it up good. At this point, I'm thinking about just making one. I don't like the 1/4" lip at the drain. If I make one, I can do it right. I kind of wish I would have just made one from the start.
IF.... 2" is the I.D., You simply cut a piece of 2" ABS pipe (which has a 2" O.D.) about 3" long and glue that in your tank and put that fitting over the piece that sticks out.

However, I believe that the 2" reducer bushing has a 2" O.D. but I could be wrong.
__________________
TrailManor Elkmont
640W solar- 230AH LiFeP04 Battery
Wavery is online now   Reply With Quote
Old 09-30-2024, 11:19 PM   #14
Dan3023
Member
 
Join Date: Aug 2024
Posts: 17
Default

I'll try that 2" ABS and see what happens!
Dan3023 is online now   Reply With Quote
Old 09-30-2024, 11:23 PM   #15
Dan3023
Member
 
Join Date: Aug 2024
Posts: 17
Default

2" ABS is 2.375" OD. I'm just going to try some 3M 5200 and goop it up. That stuff had held things on my boats for years.
Dan3023 is online now   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Elkmont black tank Wavery Trailmanor Elkmont Models 1 04-20-2024 12:52 PM
Leaking roof vent Expanderoo General Maintenance and Cleaning 39 05-17-2020 08:05 PM
Gray water tank vent behind converter BrucePerens Plumbing 3 10-26-2015 01:05 PM
Replacing the Elkmont's black water tank brulaz Trailmanor Elkmont Models 3 07-12-2011 07:29 AM
Safety Recall on **some** TM Propane tank OPDs RockyMtnRay General Maintenance and Cleaning 4 07-29-2003 07:04 AM


All times are GMT -6. The time now is 04:31 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.