TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Technical Discussions > Tires Tires Tires
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 05-03-2010, 05:34 AM   #1
mbd4kids
Senior Member
 
Join Date: May 2008
Posts: 96
Default Can't remove spare tire

Help!! We have a 1999 3023 with the spare tire mounted on the back bumper. I need to replace the spare but I can't get the bolt loose. It has a couple of plates that act like washers between the rim and the bolt, and a bit of rust. I've sprayed it (several times) with liquid wrench, tried a hammer to the end of my wench, but nothing. Any advice would be appreciated.
mbd4kids is offline   Reply With Quote
Old 05-03-2010, 05:59 AM   #2
MisterP
Guest
 
Posts: n/a
Default

If badly rusted the penetrant oil will work slowly. Spray and wait. Not much else you can do short of drilling or cutting out the bolts.
  Reply With Quote
Old 05-03-2010, 06:09 AM   #3
mtnguy
Guest
 
Posts: n/a
Default

Try an impact wrench. If you don't have 1 or can't borrow 1 from a neighbor, take the TM to any auto repair shop and have them use theirs.
  Reply With Quote
Old 05-03-2010, 07:47 AM   #4
RogerR
Guest
 
Posts: n/a
Default

You can buy a cheap impact wrench that works on a battery. It is very handy to have on the road if you have to change a tire.
I bought this one and it seems to work well.
http://www.jcwhitney.com/24-volt-cor...29&zmap=29669G
  Reply With Quote
Old 05-03-2010, 08:29 AM   #5
ShrimpBurrito
Site Sponsor
 
ShrimpBurrito's Avatar
 
Join Date: Jul 2006
Location: Sunny Beaches of Los Angeles
Posts: 3,233
Default

You might try a nut splitter to break the nut off:

http://www.acehardware.com/product/i...ductId=1292905

Dave
__________________
2000 2720SL & 2007 3124KB
2005 Toyota Sequoia
Twin Battle Born 12v 100Ah LiFePO4 (BBGC2) batteries, 300W solar on rear shell, Link 10, Lift kit, Maxxis 8008 225 75/R15 E tires
ShrimpBurrito is online now   Reply With Quote
Old 05-03-2010, 10:23 AM   #6
Bill
Site Team
 
Bill's Avatar
 
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,088
Default

Mr. P is right about patience being the key to penetrating oil. Once you have flooded the area, it also helps to tap (hard!) the frozen part in several directions - left, right, in, out, up, down - to help the oil penetrate. You might also want to try to turn the bolt in the tighten direction. All you need is a tiny bit of motion in any direction, and then you are home free.

I've never owned a power impact wrench. But back in my motorcyle days, I bought a hand-powered impact wrench. It is a cylinder a little smaller than a beer can, with a 3/8" drive socket mount on one end. Once you have the socket mounted and in place, you smack the other end with a hammer. A mechanism inside converts the forward force of the hammer blow into a tighten or loosen impact. Worked wonderfully, and cost about half the cost of even a cheap power wrench.

The hand impact wrench has one unique capability. The power drivers exert force either to the left or to the right, but that's all. But with the hand driver, I could also chuck up a Phillips (or straight) screwdriver bit. The inward force of the hammer blow pushed the bit into the slot of a screw whose head was almost enitrely stripped out, allowing me to back out those screws. Seemed like those cheap Japanese motorcycle screws were always stripping out!

I own two of those hand drivers now. I seldom need to use them - but when I need one, nothing else will do.

Here's the unit that Sears carries. Go to Sears.com and enter the Item # in the Search box.
Sears Item# 00915232000 | Model# LIS29200

Bill
__________________
2020 2720QS (aka 2720SL)
2014 Ford F-150 4WD 5.0L
Bill's Tech Stuff album
Bill is offline   Reply With Quote
Old 05-03-2010, 04:40 PM   #7
mbd4kids
Senior Member
 
Join Date: May 2008
Posts: 96
Default

Thanks all- I'll keep you posted!
mbd4kids is offline   Reply With Quote
Old 05-03-2010, 06:18 PM   #8
terryh
Guest
 
Posts: n/a
Default

Try heat. A propane torch may be hot enough. One time I had a hitch ball stuck on a bumper and my mechanic used a welding torch to heat it, and the nut backed right off. Be careful if you have used lots of penetrating solvent as it will burn.
  Reply With Quote
Old 05-03-2010, 10:03 PM   #9
B_and_D
Site Sponsor
 
B_and_D's Avatar
 
Join Date: Jun 2003
Location: Santa Cruz County, CA
Posts: 2,405
Default

I had an outside rear-view mirror that wouldn't come off of my Mercury. I held a soldering iron (a bigger one I'd bought years ago to do stained glass work, not the tiny ones you use for fine soldering) onto the bolt for a couple of minutes, and it finally came off. But I didn't put all that solvent stuff on it either, you may want to wipe it clean before applying heat.
__________________
'97 2720 & '01 Chevy Silverado 1500 4x4
2011 & 2017 Prii, 10'x18' & 10'x9' Tents
B_and_D is offline   Reply With Quote
Old 05-09-2010, 07:33 AM   #10
mbd4kids
Senior Member
 
Join Date: May 2008
Posts: 96
Default

Thanks for all of your suggestions. I ended up using a nut splitter because the man at Sears said the impact wrench wouldn't work. Mind you, he also didn't think the nut splitter would work, but it was an inexpensive try, and did work. Now on to the toilet...may be seeking more help soon!
mbd4kids is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Lesson learned: Don't neglect to check the spare tire Gwenzilla Tires Tires Tires 7 09-07-2008 08:00 PM
spare tire carrier: mod to prevent "mashed" sidewall rickst29 Frame 11 09-21-2007 10:22 PM
Unusual Sidewall Wear on Spare Tire grill-n-go Tires Tires Tires 8 10-05-2006 09:47 PM
Spare Tire stuck on rack! Larry_Loo General Maintenance and Cleaning 3 06-13-2002 05:00 AM


All times are GMT -6. The time now is 12:01 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.