TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Technical Discussions > Tires Tires Tires
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 06-23-2024, 07:45 PM   #1
JohnUSA
Member
 
Join Date: Jun 2024
Location: Pacific Northwest
Posts: 9
Default Using the TM jacks to change a tire

I've read several posts regarding changing a flat tire. Some people advocate a bottle jack on the frame, and there have been other comments simply use the jacks at each end of the TM to facilitate changing a tire.

I don't know if I'm missing something in the translation, but why would you opt for a bottle jack if you can just run up the corner jacks that have no chance of slipping?
__________________
2006 TM 2720SD, tucked behind 2016 Chevy Tahoe
2017 Pugs-Dora & Bogey
JohnUSA is offline   Reply With Quote
Old 06-24-2024, 03:36 AM   #2
Shane826
TrailManor Master
 
Shane826's Avatar
 
Join Date: Aug 2015
Location: Rochester, NY
Posts: 1,894
Default

From the owners manual:
Attached Thumbnails
Click image for larger version

Name:	IMG_2611.jpeg
Views:	517
Size:	457.2 KB
ID:	23331  
Shane826 is online now   Reply With Quote
Old 06-24-2024, 06:07 AM   #3
Bill
Site Team
 
Bill's Avatar
 
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 10,187
Default

At 5000 pounds each, the corner jacks have plenty of capacity. I have changed a tire using the corner jacks alone, but I'm not real comfortable doing it. They can seem a little wobbly as big semis blow by the trailer, and they can be extra-hard to crank up if they are gritty after their emergency trip to the edge of the roadway. My procedure (below) is simpler to do than to read about.

First, I carry a short 2-ton bottle jack, about $15 at Amazon and others. It needs to be short because after a blowout, the frame of the TM will be close to the ground. My bottle jack has a 7" collapsed height and a 6" lift range. It also has a 6" screw extension in the center.

I also carry several (at least 6) short pieces of 2x6 board, plus a hunk of 4x4 - each 12-18 inches long. These pieces are used primarily for leveling in the campground, so carrying takes no extra space, but be sure they are accessible when you are pulled over beside the road.

Don't forget that somewhere in this process, you will need to get the spare tire off its storage rack, and flopped on the ground next to the camper. I do this about midway through the jacking.

When it is time to remove the bad tire, put a piece of 2x6 on the ground under the frame ahead of the tire. Screw the bottle jack core down, and set it on the board under the frame (NEVER the axle!). If the TM is too close to the ground for the bottle jack to fit, use the stabilizer jacks to raise the TM a bit, until the jack can be placed. On the other hand, if the jack fits with space to spare, raise the screw core until it contacts the frame.

Pump up the bottle jack to its maximum height. With a 2-ton rating, pumping it is really easy - much easier than cranking the corner jacks under load. Most likely it will not be up far enough, so lower the stabilizers all the way to the ground, letting them support the weight of the trailer again. Lower and remove the bottle jack, screw the core down all the way, add 2 or 3 boards to the pile, re-insert the bottle jack, and pump it up all the way up again. Lower the stabilizers further, until they again support the weight of the trailer. If the trailer still isn't high enough, remove the bottle jack, screw down the core, put more boards in the pile, jack it again, and lower the stabilizers again. Don't use boards narrower than 6 inches, as the pile tends to get wobbly as it get higher on soft or uneven ground.

When you finally get almost to the height needed to remove the bad tire, use your lug wrench to loosen the lug nuts a turn or so. Then continue jacking, adding boards as needed to get high enough to pop on the fully-inflated spare tire.

Reverse the process on the way down - it is quick and easy because you now have an inflated tire on the TM.

I can change a tire in less than 10 minutes, from getting out the tools to driving away, using this sequence. The bottle jack makes it easy, and safe.

Bill
__________________
2020 2720QS (aka 2720SL)
2014 Ford F-150 4WD 5.0L
Bill's Tech Stuff album
Bill is offline   Reply With Quote
Old 06-24-2024, 09:14 AM   #4
JohnUSA
Member
 
Join Date: Jun 2024
Location: Pacific Northwest
Posts: 9
Default

Very detailed, thanks. I'll be cutting up a 2x6 this afternoon.
__________________
2006 TM 2720SD, tucked behind 2016 Chevy Tahoe
2017 Pugs-Dora & Bogey
JohnUSA is offline   Reply With Quote
Old 06-24-2024, 10:25 AM   #5
rickst29
yes, they hunt lions.
 
rickst29's Avatar
 
Join Date: Aug 2005
Location: Reno, NV
Posts: 1,360
Default The problem with using the corner 'lift jacks' alone:

The corner lift jacks have plenty of vertical strength, but they can 'accidentally' tilt a large amount (street-side to curb-side, along the length of the screw) when they are not holding the upper TM frame and body EXACTLY level.

In changing a tire (i.e., a wheel rim with the tire already on it), your normal approach with either a car or truck would be to lift only the side with the bad tire, leaving tires on the "other side" flat on the ground. DON'T DO THAT by using only a pair of the TM lifts, because the whole TM will tilt away from the raised side towards the un-raised side.
- - -
Bill's tactics are good, using a bottle jack to perform nearly all the lifting. Adjustable jack stands can also be used to provide enough height while not allowing the TM body to "slide" in either direction.
__________________
TM='06 2619 w/5K axle, 15" Maxxis "E" tires. Plumbing protector. 800 watts solar. 600AH LiFePO4 batteries, 3500 watt inverter. CR-1110 E-F/S fridge (compressor).
TV = 2007 4runner sport, with a 36 volt "power boost".
rickst29 is online now   Reply With Quote
Old 06-24-2024, 09:57 PM   #6
Kidkraz
Site Sponsor
 
Kidkraz's Avatar
 
Join Date: Mar 2013
Posts: 1,083
Default

I would add one bit of info to Bill's directions. Break the lug nuts loose before taking the wheel completely off the ground. I say that from experience, if the wheel is off the ground enough, it will spin. You'll have to then lower the camper down to prevent the rotation to break the lug nuts free enough to remove them to swap out the tires. In swapping out a tire, due to a leaking valve stem, I relearned this.
__________________
2013 2619
80 watt solar panel/swing hitch/low profile A/C.
Enduro 4445 caravan mover
2016 Dodge Ram 1500 V8 Hemi
Installed powered folding tow mirrors

Stopped playing with airplanes, now I just enjoy watching them fly by.
Kidkraz is online now   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Is my Dexter Axle still adequate or is it something else? coralcruze Tires Tires Tires 24 04-04-2022 02:48 PM
My first visit to the new TM plant in SD kempert Off Topic 2 05-01-2019 05:12 PM
Why TM batteries are not (normally) charged by Tow Vehicles rickst29 Electrical 10 04-17-2016 03:54 PM
Garage Clearance -- Reduced TM Tire PSI hingarfi Frame 0 04-14-2005 12:52 PM
Using a battery charger to run the TM refer & fan RockyMtnRay How to and Modifications 17 07-27-2003 08:04 PM


All times are GMT -6. The time now is 05:07 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.