TrailManor Owner's Forum - View Single Post - Using a battery charger to run the TM refer & fan

**Denny_A** · 07-24-2003, 11:59 AM

[quote author=Carol link=board=7;threadid=908;start=0#msg7241 date=1059019837]
Hi!

Thinking about using a dryer extension cord to plug in the TM in the closed position further (after having trouble finding a 3 ft flat dryer extension cord), it dawned on me that I could use my adapter (30 amp to 15 Amp) and plug in a regular 3 prong extension cord. I don't really need 30 amps for this situation since the air conditioner will definitely not be running!

I haven't tested this theory out as yet as the TM is currently stored in the garage. The only concern would be if the adapter will fit into the storage compartment.

Thanks again for the creative solution!

Carol
[/quote]

Carol,

I just finished what you suggest - a couple of days ago.

Purchased a 6 foot grounded, 15 amp extension. The female end was not included since the extension was intended to replace cords on an appliance. I cut it down to 3.5 feet and added the female plug.

Using the 30 to 15 amp adapter, I pulled the TM plug INTO the storage compartment and connected the new 15 amp extension. Ran the 15 amp cord down the side of the body, pinned it to the torsion bar adjuster bolt. Finally the male end of the cord rests under the trailer on the frame cutout thru which the torsion bar runs. Another tiewrap is used to cinch the plug to the frame.

It's easy to connect and won't get rained on overnight. At the campground there are two tiewraps to snip to revert to normal ops.

The key factor is that the 30 amp TM plug can be EASILY pushed into the storage compartment. Eliminates the space issue. All tested. It works!

Denny_A

P.S.: Pondered the setup after posting this. It occurred to me that I might not have to disconnect the contraption at all.

Sure enough. I brought the female plug around and under the trailer (remember the tiewrap on the torsion bar adjuster bolt), across to the plug tiewrapped to the frame, and mated them. I first passed the cord above the uppermost torsion rod on it's way to the male plug. The plugs rest on top of the lower part of the torsion rod pass-thru cutout, and well aft of the rods. It's secure and weather proof. Didn't even need another tiewrap. The cord, near the adjuster bolt, DOES rest ever so lightly on a torsion rod, but since the rotation of the rod is 90 degrees max, wear on the thick neoprene cover will be a non-factor, IMO. ;D

07-24-2003, 11:59 AM	#12
Denny_A Former TM Owner Join Date: Jul 2002 Location: Greenville, WI Posts: 517	Re:Using a battery charger to run the TM refer & fan [quote author=Carol link=board=7;threadid=908;start=0#msg7241 date=1059019837] Hi! Thinking about using a dryer extension cord to plug in the TM in the closed position further (after having trouble finding a 3 ft flat dryer extension cord), it dawned on me that I could use my adapter (30 amp to 15 Amp) and plug in a regular 3 prong extension cord. I don't really need 30 amps for this situation since the air conditioner will definitely not be running! I haven't tested this theory out as yet as the TM is currently stored in the garage. The only concern would be if the adapter will fit into the storage compartment. Thanks again for the creative solution! Carol [/quote] Carol, I just finished what you suggest - a couple of days ago. Purchased a 6 foot grounded, 15 amp extension. The female end was not included since the extension was intended to replace cords on an appliance. I cut it down to 3.5 feet and added the female plug. Using the 30 to 15 amp adapter, I pulled the TM plug INTO the storage compartment and connected the new 15 amp extension. Ran the 15 amp cord down the side of the body, pinned it to the torsion bar adjuster bolt. Finally the male end of the cord rests under the trailer on the frame cutout thru which the torsion bar runs. Another tiewrap is used to cinch the plug to the frame. It's easy to connect and won't get rained on overnight. At the campground there are two tiewraps to snip to revert to normal ops. The key factor is that the 30 amp TM plug can be EASILY pushed into the storage compartment. Eliminates the space issue. All tested. It works! Denny_A P.S.: Pondered the setup after posting this. It occurred to me that I might not have to disconnect the contraption at all. Sure enough. I brought the female plug around and under the trailer (remember the tiewrap on the torsion bar adjuster bolt), across to the plug tiewrapped to the frame, and mated them. I first passed the cord above the uppermost torsion rod on it's way to the male plug. The plugs rest on top of the lower part of the torsion rod pass-thru cutout, and well aft of the rods. It's secure and weather proof. Didn't even need another tiewrap. The cord, near the adjuster bolt, DOES rest ever so lightly on a torsion rod, but since the rotation of the rod is 90 degrees max, wear on the thick neoprene cover will be a non-factor, IMO. ;D