PDA

View Full Version : To plug or not to plug ?


Goodyear Travels
10-08-2006, 12:18 PM
Getting the answers to questions would be infinitely more difficult without the knowledgeable and good-hearted folks in this forum. I'm very grateful for your help. I've been deliberating about plugging a hole in a piece of metal trim along the roof edge of our new 2720sl (just beyond the end of the awning). A similar hole exists on the opposite side of the trailer in the same location. I've hestitated because I'm not sure if the holes function as drainage or vapor vents. Did someone with a Makita just get carried away and should I plug the holes with suitable screws and silicone, or do they serve a purpose ? I've attached a photo for your review and a pic of my Aussie buddy, Deacon. Eric
Ps Only 5 more days until our 1st excursion in our new TM.
We're heading to the Prescott National Forest (Lynx Lake) and will be camping at about 5K ft.

pbuck1
10-08-2006, 12:37 PM
Eric,
See this link:
http://www.trailmanorowners.com/forum/showthread.php?t=2978&highlight=drainage

-Paul

idaho-steve
10-08-2006, 12:38 PM
Eric, For what it is worth, I have no such holes on either side of my '02 2720SL. In fact, my awning is positioned more to the edge so that it would cover such a hole. A call to the factory might be the best bet since the holes may serve some function since they are on both sides. Let us know. Heck, maybe I should be adding some holes :-) Steve

Bill
10-08-2006, 01:08 PM
Like Steve, I don't recall having them on my 2002 2720SL, but I do have them on my '06. Drainage sounds right to me, although I can't for the life of me figure out what is being drained, and why it needs draining. Vince's explanation (in the thread that Paul referenced) sounds reasonable, so I guess I won't mess with it. More to the point, the fact that they appear on so many TMs suggest that they were put there on purpose, and should NOT be plugged.

On the other hand, if you decide to plug them, let us know the outcome. We're all curious!

Bill

Goodyear Travels
10-08-2006, 01:27 PM
Thank you all for the advice and especially Paul's referenced thread. I'll leave the holes alone and go after a few seams on the underside of the trailer with the silicone.

PopBeavers
10-08-2006, 08:36 PM
My 2005 TM 2720 has the same holes, but they are drilled slightly higher, right at the curve between the top and the side.

Simon3xUD
10-09-2006, 10:54 AM
I've attached a photo for your review and a pic of my Aussie buddy, Deacon.

Hooray! Another TMing Aussie :). Panda, Dia, and Ally all offer a wiggly welcome to Deacon :D. I'm sure Deacon will love his new TM as much as my "kids" love theirs!

camp2canoe
10-09-2006, 03:47 PM
When we bought our 2619, the technican who did our "walk through" pointed out the holes referred to, insisted that the holes should NEVER be plugged and told me that they were drilled to equalize pressure. I just sort of took this as an article of faith without much thought. Now I'm wondering what pressure they might equalize? - Camp2Canoe

Bill
10-10-2006, 07:42 AM
How about calling up the dealer and asking? I'd LOVE to know the explanation for that one. The only pressure differential I can imagine is from the wind pushing on the front of the trailer as you drive, the suction behind the trailer, or the Bernoulli pressure difference from the wind slipping along the side of the trailer. I'm not sure why one would want to "equalize" any of those pressures - and I'm REALLY not sure how they would be equalized by holes in that location.

Bill

CAmark
10-10-2006, 01:19 PM
I recall this being addressed here within the last year...and finally found it again...note that the Factory has weighed in here already...http://www.trailmanorowners.com/forum/showthread.php?t=4181&highlight=awning+hole
mark