TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor General Discussions > TrailManor Pictures
Register FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 04-30-2017, 05:48 PM
Larryjb Larryjb is offline
Site Sponsor
 
Join Date: Nov 2016
Location: Vancouver BC
Posts: 450
Default Pictures newbies won't have seen before

When I was looking for a TM, I was very curious about some of the technical aspects of TM construction. Sorry, these are not going to be picturesque!

One of the big questions, what years had metal framing? This varies, and cannot be pinned down to a specific year. However, you can check without removing any screws. Just peek underneath and inside one of the pocket stops. These are located where the lift arm attaches to the upper shell. There are 8 of these in total.
Click image for larger version

Name:	metal framing at pocket.jpg
Views:	466
Size:	29.5 KB
ID:	15176

Not all wood can be eliminated. One place is for the bag seal, and this wood needs replacing once in awhile. It's hard to see as my camera was fighting with the bright sky and dark pocket. Much of the wood is rotted in this image and will need replacing. It shouldn't be very difficult. When the bag seal is removed, chip or blow out the remaining rotted wood, clean with dilute bleach, rinse well (you don't want bleach remaining on metal, it can erode metal). Then replace with 1x1 treated wood. Other's may have their own suggestions for this repair, but whatever solution, it won't be very bad. Nothing like what Maria went through!
Click image for larger version

Name:	rotted wood for bag seal.jpg
Views:	457
Size:	34.0 KB
ID:	15177

Trying to figure out where those wasps were coming from?
Click image for larger version

Name:	wasp nest.jpg
Views:	423
Size:	33.7 KB
ID:	15178

Here is a good shot of the torsion bar. Tightening the bolt pushes on the short length of the "L", increasing tension on the torsion bar.
Click image for larger version

Name:	Torson bar.jpg
Views:	410
Size:	57.3 KB
ID:	15179

Here you can see how the shell is attached to the lift bar. There is a thicker aluminum plate which is attached to the aluminum frame inside. The outer skin is damaged on mine, exposing the inner plate. The tear here will not affect the function of the lifting mechanism, but there may be sharp edges so a stainless fender washer may be a good idea here.
Click image for larger version

Name:	lift bar support bolt.jpg
Views:	328
Size:	43.5 KB
ID:	15180
__________________
Larry

2002 Tahoe
2001 2720SD
Reply With Quote
  #2  
Old 05-04-2017, 09:53 PM
wbmiller3's Avatar
wbmiller3 wbmiller3 is offline
Site Sponsor
 
Join Date: Oct 2004
Location: Southeast of Houston, Texas
Posts: 997
Default

Good info even for veterans! I've never looked up into my trailer's pocket stops, but I am going to now!
__________________
Bill
http://eclectichouston.mynetgear.com
https://www.facebook.com/wbmiller3
2003 Expedition towing 2001 2619; lift kit & 15" wheels
Reply With Quote
  #3  
Old 05-05-2017, 08:43 AM
Bill's Avatar
Bill Bill is offline
Moderator
 
Join Date: Feb 2003
Location: The mountains of Scottsdale, AZ, and the beaches of Maine
Posts: 7,963
Default

Really nice work, Larry! Glad to see it.

Bill
__________________
2006 2720SL swing tongue, 15" tires
2014 Ford F-150 5.0L - "The Moose"
Bill's Tech Stuff album
Reply With Quote
  #4  
Old 05-05-2017, 10:51 AM
Larryjb Larryjb is offline
Site Sponsor
 
Join Date: Nov 2016
Location: Vancouver BC
Posts: 450
Default

There will be more to come as I tinker!
__________________
Larry

2002 Tahoe
2001 2720SD
Reply With Quote
  #5  
Old 06-25-2017, 04:13 PM
Larryjb Larryjb is offline
Site Sponsor
 
Join Date: Nov 2016
Location: Vancouver BC
Posts: 450
Default Furnace box

I noticed the seat above the furnace seemed loose. When I raised the cushion, I saw that one of the structural supports had come free from the staples:
Click image for larger version

Name:	CPA_DSC1484.jpg
Views:	131
Size:	67.7 KB
ID:	15584

Drilled, countersunk, and screws:
Click image for larger version

Name:	CPA_DSC1485.jpg
Views:	120
Size:	61.1 KB
ID:	15585

To answer an earlier, but now irrelevant question I had before, it would be quite easy to move the furnace if you wanted to convert a sofa model into a dinette model. The most technical parts would be rerouting the gas and electrical lines.
__________________
Larry

2002 Tahoe
2001 2720SD
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
How to shrink pictures before posting them Bill TrailManor information you won't find anywhere else 0 03-24-2015 12:59 PM
How to attach pictures to posts Bill TrailManor information you won't find anywhere else 0 03-24-2015 11:16 AM
Pictures & Albums Tutorial commodor47 TrailManor information you won't find anywhere else 0 07-28-2008 07:38 PM
Chesapeake RV solutions event. Mods w/ PICTURES Debian Dog General discussion 5 05-15-2006 08:34 AM


All times are GMT -6. The time now is 07:41 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2017, vBulletin Solutions Inc.
Copyright 2011 Trailmanor Owners Page.