TrailManor Owner's Forum  

Go Back   TrailManor Owner's Forum > TrailManor Technical Discussions > Plumbing
Register FAQ Members List Calendar

Reply
 
Thread Tools Display Modes
Old 12-24-2013, 07:32 PM   #1
snapfish
New Member
 
Join Date: Jan 2013
Location: San Bernardino Mountains
Posts: 4
Default Suburban 6 Gallon Water Heater SW6DE maintenance.

Hello

I bought my 2011 TrailManor used.
A few months later, I was reading the manuals that came with the trailer and it said that my Suburban 6 Gallon Water Heater SW6DE Operates on Lp Gas and 1440 Watt 110VAC. It also says the electric switch is right on the water heater. So I took a look and the little rocker switch is there and was in the “ON” position.

Very excited with my new discovery (LOL), I turned off the switch to the gas water heater. Next day, the water was cold as ice.
I started to troubleshoot, just to find that the electric reset switch did not work. I checked for electric current, and found readings to be normal as per the troubleshooting manual.
This started to drive me nuts. So I decided to remove the electrical heating element, and inspect behind the thermostat and manual reset switch buttons (Also I removed the rubber cover.)
Sure enough, I found one fuse wire burned and was not completing the electrical reset circuit. (see attached pics).
In addition, I found the heating element completely fried. It was very corroded (possibly the cause of the funny water taste)
I removed the water heater Anode rod and it looked like it is about 50% eroded.

The removal and re-install of the new parts are very easy and can be done in less than 30 minutes once you have the right parts on hand.

Here are the replacement parts numbers:
Suburban Screw In Electric Element 1440W = 520789
Suburban Water Heater Anode Rod Aluminum = 232768
Both you can find on ebay and Amazon for cheap. (Heating element can be found at Lowe’s and Home depot too for around $7-$9.)

Here is how to replace the parts:
You will need a 1-1/2" socket to change the heating element out. It needs a 1.5 inch socket which I bought at Lowes for $9. Don't buy a deep well socket because (based on your heater) it might no clear the gas plenum.

1- Disconnect the battery (negative side), and turnoff the gas/ propane, and water to the trailer, and turn off the electric on/off switch at the water heater tank.
2- Remove the two wire screws on top of the heater element. Push the two wires to the side.
3- Using the 1.5 socket, remove the heater element and let the water drain.
4- Using the 1.5 socket, remove the heater Anode rod.
NOW, It may be a good time to clean and flush the tank with a garden hose to remove any sediments or junk that may lay on the bottom of the water heater.
5- Screw in the new Anode rod.
6- Screw in the new heating element. Hook up the wires and put any covers back on.
7- Turn the water on to the tank.
8- Open all faucets inside the Trailer and let the air come out until no more bubbles in water, and water heater tank is now full with water.
9- Turn the electricity back on.
10- Turn on the electric switch at the water heater tank.
11- Wait 15 minutes or so and turn on the hot water faucets (you should get hot water.)
12- Turn off the electric switch, let some hot water out of the faucets and cold water into the tank.
13-Turn on the Gas/ Propane and test as well (as in step# 11.)


Thanks
Attached Thumbnails
Click image for larger version

Name:	IMG_1166-2.jpg
Views:	659
Size:	113.8 KB
ID:	9458   Click image for larger version

Name:	IMG_1148-2.jpg
Views:	664
Size:	99.8 KB
ID:	9459   Click image for larger version

Name:	IMG_1141-2.jpg
Views:	628
Size:	108.5 KB
ID:	9460   Click image for larger version

Name:	IMG_1151-2.jpg
Views:	662
Size:	116.6 KB
ID:	9461   Click image for larger version

Name:	IMG_1158-2.jpg
Views:	661
Size:	54.8 KB
ID:	9462  

__________________
SnapFish :silly::silly:
snapfish is offline   Reply With Quote
Old 12-25-2013, 06:30 AM   #2
rvcycleguy
TrailManor Master
 
Join Date: Oct 2011
Location: New Braunfels, Texas
Posts: 919
Default

Something to keep in mind Snapfish with the electrical switch in the ON position is that when you plug in the RV power cord, it immediately energizes the WH element. If the WH tank does not have water in it, it fries the heating element within seconds. That may have been the PO issue and why you found it in that condition. The routine for most owners here is to attach the water hose and run both sides (cold & hot) at the sink faucet before plugging in the power cord.
__________________
rvcycleguy

TM-2002 3124KB
TV-2003 Toyota Tundra V8 4.7L. Fact. Tow Pkg, air bags
2006 Suzuki Boulevard C50c Motorcycle- crashed- parted out
1956 Royal Enfield Bullet 500 Motorcycle-sold
2006 Harley Road King
rvcycleguy is offline   Reply With Quote
Old 12-26-2013, 06:35 PM   #3
snapfish
New Member
 
Join Date: Jan 2013
Location: San Bernardino Mountains
Posts: 4
Default

Quote:
The routine for most owners here is to attach the water hose and run both sides (cold & hot) at the sink faucet before plugging in the power cord.
rvcycleguy- I think that is the best advice, and best method to insure that the water heater tank is full of water before running the water heater (that being Gas or electric.)

Thank you very much for the excellent tip
__________________
SnapFish :silly::silly:
snapfish is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Water Meter used to fill the tanks Brittany Dogs Tips and Tricks 9 08-07-2013 09:30 AM
Hot water heater purge issue MarkoPolo Appliances 11 04-21-2013 10:39 PM
Water Heater Info (How I fixed my SW6DE)!!! Camper One Plumbing 4 11-19-2012 09:16 AM
Water Heater (Suburban SW6DE) ib4classics Plumbing 10 06-03-2010 06:22 PM
Water heater anode length-3 gallon H20 heater B_and_D Appliances 0 08-20-2007 12:08 PM


All times are GMT -6. The time now is 05:45 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 2022 Trailmanor Owners Page.